Sintral tab

Empty cycles until all yc are in home position section

S0Y

With the checkbox activated, the yarn carriers are brought into their home position at the start of the pattern. The S0Y command is entered in the knitting program (Sintral).
In the Further commands field, with S0Y appears the the fabric take-down specification W0.

Machine stop (MS) when S0Y

The machine stops when the yarn carriers are in their home position. This checkbox can only be activated together with the S0Y checkbox. The MS command is entered in the knitting program (Sintral).
With the check boxes S0Y and Machine stop (MS) with S0Y activated, the entire entry in the knitting program has the following appearance:
S0Y #99=1

Text of message

The Text CHECK YARN CARRIER is entered by default. This is applied in the knitting program (Sintral) together with the PRINT command and shown on the machine display. The entry in the knitting program is as follows:
PRINT/CHECK YARN CARRIER/

Further commands

Input field for additional Sintral commands applied while generating the knitting program.

Sintral/Setup Section

List field
Setup1 always in Sintral

Put the Setup data in the Sintral file
: Only with Setup1

Enter stitch length in [mm]

Save the stitch tension as a mm value in the Setup file, otherwise as an NP value.
: With a specified mm value, the value no longer needs to be converted on the machine when Yarn Length Measuring is used.

Group transfer rows

Group several consecutive transfer rows to a jacquard line in the jacquard (*.jac). This saves jacquard lines.

Minimize by functions (not for STx11 machines)

Call-up identical Sintral blocks by functions. This reduces the memory requirement of the machine.
: The Sintral line number can not be displayed in the Jacquard control column with the check box active.

General stitch cam correction section

NPK:

Select a value from -2.0 to +2.0 in steps of 0.1. This correction value is applied to the knitting program (Setup). On the machine all stitch cams are also adjusted by the specified NPK value in addition to the value specified in the Sintral. Default is without entry.

List field
NPSK:

Select a value from -2.0 to +2.0 in steps of 0.1. This correction value for the second stitch tension is applied to the knitting program (Setup). On the machine all stitch cams for the second stitch tension are adjusted by the specified NPSK value in addition to the value specified in the Sintral. Default is without entry.

: Only CMS 730 S / CMS 830 S

Carriage speed section

: The specified values are applied in the knitting program (Setup).
If a setup file with the Import MC-SETUP function is imported in the MC Program menu, then the MSECK value from this file also appears in the Configuration.

With Knots (MSECK) [0.00 = ML]:

Specify what speed the machine is to knit at when a small knot is present in the yarn. The value range is from 0.05 to 1.2 in steps of 0.05.
The value 0.00 equals ML (machine slow).

Rows:

Select number of rows (strokes) which are to be processed at this speed so that the knot is also processed.

With Intarsia (MSECI):

Specify what speed the machine is to knit at when using intarsia yarn carriers. The value range is from 0.05 to 1.2 in steps of 0.05. The specified value is applied in the knitting program (Setup).

with clamping (MSECC) [0.00 = default]:

Set the speed outside the needle bed for bringing the yarn carrier in the clamp or taking it out of the clamp.
The value 0.00 corresponds to the default speed of 0,5 (CMS-C: 0.30)

Presser foot section : Only CMS 730 S / CMS 830 S

active when knitting

Use the presser foot in the knitting system.

active when transferring or splitting

Use the presser foot in the transferring system.