What was new in CREATE PLUS V2.0 and V2.1

Editing in the Symbol View

• Vertically Split View
• Tile the symbol view into two side by side views by the Split View Vertically button of the status bar.
• View and edit the left and right edge of big patterns at the same time.
• Even at a large zoom level without additional scrolling.
• 
• The drawing tools work across the board.
  You can start and end the drawing action in different halves of the view.
• Splitting the expanded preview
• Splitting the symbol view after technical processing
• 
• Single Click Mode for Drawing
• Up to now within the control columns only
• Now within the needle area of the symbol view as well
• Key combination 1
  
• Key combination 2
  双击
• : Drawing by the single click mode is possible even within the double click mode.
  → Start to draw with the mouse button pressed after a first click.
• Drawing with a module with repetition
• Drawing in modules with repetition element (pointelle module e.g.) is reduced to two clicks defining the start and the end of the action.
  In between, you define the with by drawing up.
• : Hit the CTRL + Alt key combination before the first click and move the mouse in order to draw in the module according to the previous method.
  First specify the width which you can then enter several times.
• Copy selection (CTRL + C)
• If you copy a selection, the individual parameters of the clipboard appear in the user control to switch them on or off.
• By V2.0, the user control appears in case of each copy action with the应用控制列 setting disabled (screen of V2.0).
• 
  Each time, you had to repeat the individual setting.
• In V2.1:
  The setting once done is kept for each new action of copy or insert during the current session.
• 注意！ The setting once done is kept for each new drawing action with modules during the current session.
• Insert Selection
• In order to insert empty rows, you had to use the 插入绘图属性 option without having selected a drawing attribute.
• Now the 插入空行 option is available to insert empty rows.
• 
• Extension of Key Combination O (打开)
• Up to now, you could only open the module below the cursor in the symbol view by O key.
  You could open CA or MA of this row via the control column only.
• Now you can open CA and MA by the O key as well if they are assigned to the row below the cursor.
  If necessary, this will open the three corresponding editors (Module, CA, MA).
• You can open CA or MA by the O key if the cursor is positioned over an assigned CA or MA in the control column.
• You can open the corresponding Setup Data by the O key if the cursor is positioned in a control column with the 在表中显示 context menu.
• : The same behavior is valid for the expanded symbol view and for the symbol view after technical processing.

• Comments
• You can place comments exactly to the needle in symbol view of the pattern. You will find the menu items in the context menu of the view.
• 
• You can move the comments by the left mouse button.
  Deleting and resetting the move are available in the context menu of the comments.
• You can navigate through the comments by the new 注释 tool window.
• 
• You can control the display of the comments by the status bar of the view.
• 

Fabric View

• Status Bar
  Now, you can save your individual settings of the view.
  
• 保存视图选项
• 还原外观
• 重置视图选项

Fully Fashion

• DXF 导入
• Improved usability of the 缩放 function.
• After opening the file, the 缩放 slider is positioned in the center.
• Default 1.00 (= 100 %), step width 0.01 (= 1 %).
• New function 移动织片
• 
• With the function enabled, the fabric piece selected in the 织片 table will be positioned by the point of the lower left of its circumscribing rectangle to the point on which you click with the left mouse button.
  
• : A multiple selection is possible
• You will find the new 织片 function in the context menu of the fabric pieces in hte 原点对齐 table.
• With it, the 0 point of coordinates is set to the point of the lower left of the circumscribing rectangle.
• Shape element 褶
• Optimized template 褶
• Without any time-consuming post editing
• The shape elements orientate themselves matching the left or right side of the fabric piece.
• 
• The symmetrical variant of the shape element is omitted.
• : In the context menu of the shape under 添加新模型元素....

• 结束层
• Up to now, you could indeed edit on the pattern data of the lined shape but only for a complete shape line.
  You could not edit exactly to needles.
• Now, the 结束层 is available.
• 
• Example as image:
  Rasterizing error due to the narrowing width of the shape line which does not allow the narrowing of row 466.
  In addition, the narrowing of row 464 is not correct due to stitch at 模型外.
• Without editing the lined shape, you can fix both of the errors in the 结束层.
  Create this layer by the 创建结束层 button.
• 
• Mask out the narrowing at marked position of the pattern by the 悬停模型淡化 drawing attribute.
• : The fading-out by the shape line will be masked out.
  The needle action of the pattern appears.
• 
• Draw in both of the shape symbols for narrowing and the needle action for fading-out.
• By the 结束层橡皮擦 drawing attribute you can delete data of the 结束层.
• 
• By the 删除结束层 context menu of the button you delete the complete Finishing Layer.

多片编织

Knitting two fabric pieces side by side is possible if the pattern contains a comb start.

• Two ways of knitting several pieces
• The 编织区域颜色 tab of the配置 tool window contains both variants.
• Duplicate Pattern
• 
• Two Positioned Shapes
• 
• : If two shapes are positioned side by side, the 多片编织 option must be disabled as otherwise four fabric pieces would be given to the technical processing.
• In contrast to M1plus, no special technical processing is required for multi-piece knitting.

Output of Warnings and Errors

The technical processing may lead to warnings and errors (abort of processing). The output of these messages is reworked.

A message contains the following parts:

1. Number of the message with link to detailed help.
2. Type of the message (here warning)
3. Text of the message.
   A link to the pin will appear if the message can be located.
   
4. Toggle the display of pins
5. Delete message
   (available for warnings only)

Further Improvements:

• Several messages of the same error will be combined to one message.
  Therefore, several pins appear within the pattern to which you can navigate.
• 
• The upright Pin shows the selected message.
• If the message refers to a control column, a pin will be set to the control column and it will be displayed.

电子送纱器

Controlled feed wheels are supported.

Activate them by 配置 → 机器属性.

• 串行的 MEMMINGER-IRO
• EFS 820
• EFS 920
• CAN MEMMINGER-IRO
• EFS 820
• EFS 920
• CAN BTSR
• CAN LGL

• New tab 送纱器组合
• Here you assign yarn carriers to a group, which shall work with common settings.
• 导纱器 tool window → 导纱器视图
• 
• Control column 送纱器
• Here, you can allocate the desired feed wheel index SFOI to the knitting rows.
• 
• 送纱器 Setup Data
• Here, you can specify the parameters for the feed wheels.
• 

Knitting Machine with Additional Beds

• CMS 730 T machine is a available to select
• There are special narrowing, widening and binding-off modules for 全成形 FF which you have assign to the shape lines.
• 
• Additional control columns for racking are available among the control columns of the pattern.
• 

Name of the Knitting Program

• Up to now, the name of the knitting program was build from the name of the pattern.
• Now you can select how the knitting program name will be created:
• 项目
• 花型
• 项目和花型
• The presetting of 选项, 常规 tab works globally until to its modification.
• 

Check of Knitting Program

It was not possible to cancel the common check of several knitting programs by theSintral 检验.

• Now, you can cancel the Multiple Processing .
• 
• The Sintral 检验 icon of the 花型 tool window will be marked if the pattern was edited and the knitting program was re-created after the check.
• 

Send the knitting program to the knitting machine

• You can send the knitting program directly to networking knitting machines.
• Set-up the online connection to the machine in 配置, Registerkarte 机器属性 tab.
• IP 地址：
• 联机 ID：
• 
• 发送 function of the Sintral ribbon group
• 

Please Report Errors with The Project File

STOLL and KM.ON are two successful brands of the KARL MAYER Group combining their expertise and creativity for highest customer benefit.

• From one side, STOLL is leading in flat knitting technology and is a solution provider with a process know-how.
• In the other side, KM.ON is specialist on software products, digital solutions and services for the textile business.

To clarify the membership in KM.ON, the former STOLL software (CPS) was renamed into CREATE PLUS .
The PLUS in the name stands for the complete integration of all features of CREATE DESIGN .